Your Terrain wall art - how to put it together

9 wood pieces · 18 bolts · 36 in × 24 in board · 11/18/2026

Everything is labelled, so this is mostly matching labels. Each wood piece has a number. Each bolt has a label made of a piece number and a letter (1a, 1b, 2a ...), and the hole it goes through in the board has the same label written beside it on the back. Match them and it cannot go together wrong. The order is: lights into the back of the board, then the bolts, then the wood pieces on the front.

What is in the box

☐ Backing board136.0 in × 24.0 in, 18 small holes and 3 round light openings; every hole has its label written next to it on the back
☐ Wood pieces9numbered 1 to 9 on the back
☐ Hex bolts180.250 in thick, in 9 lengths: 2 × 6.50 in, 2 × 6.00 in, 2 × 5.50 in, 2 × 5.00 in, 2 × 4.50 in, 2 × 4.00 in, 2 × 3.50 in, 2 × 3.00 in, 2 × 2.75 in; each one is labelled (1a, 1b, 2a ...)
☐ Nuts543 for every bolt (7/16 in wrench)
☐ Lights3one per opening, F1 to F3

You will need: a ruler or tape measure (there is one printed on the last page), a 7/16 in wrench (an adjustable one is fine) and a second one or pliers to hold a bolt head, two old towels or a blanket, two sturdy boxes or stacks of books of the same height (at least 8 in tall) to rest the board on, a drill with a small bit for the wall screws, and a second person to turn the board over and hang it.

Back map - the board seen from the BACK

↑ top edge · use this map for the lights and the bolts (steps 1 to 4). It is the front map flipped over, like the board.

F1F2F31234567891a1b2a2b3a3b4a4b5a5b6a6b7a7b8a8b9a9b

What the maps show

A number in a circle is a wood piece. The same number is written on the back of the piece.
A dot with a label (2a) is a hole in the board. The bolt with the same label goes through it. The number says which piece the bolt holds (piece 2); the letter just tells the bolts of that piece apart.
A thin grey line is where two pieces meet - the cut between them.
A dashed circle (F1) is a round light opening in the board. The light goes in from the back.
The black frame is the edge of the board. The top of the map is the top of the finished art.

Front map - the board seen from the FRONT

↑ top edge · use this map for the pieces (step 6) and when the art hangs on the wall.

F1F2F31234567891a1b2a2b3a3b4a4b5a5b6a6b7a7b8a8b9a9b

Step by step

  1. Set up. Spread a towel or a blanket on a table or a clean floor so nothing gets scratched. Stand the two boxes (or book stacks) on it, a little closer together than the board is long, and lay the backing board across them back side up - the side with the labels written next to the holes. The middle of the board is now off the table, so you can reach under it. Turn the board so its holes match the back map (the top edge of that map is the top edge of the art).
  2. Fit the lights. Fit each light into its round opening from the back (F1 to F3 on the back map). Follow the light's own instructions for the wiring, and lead the wires toward the edge of the board where the power will be. The lights shine through the gaps between the pieces.
  3. Put the bolts in. Take any bolt and read its label (for example 1a). Find the hole with the same label on the back of the board. Drop the bolt through that hole so its head rests on the back of the board and the threaded end points down through the gap under the board. Reach under and spin one nut onto it, finger-tight, so the bolt cannot fall out. Do this for every bolt - every hole gets its own bolt, and the bolts are different lengths on purpose.
  4. Turn the board over. With your helper, lift the board, move the boxes away, and lay it face up on the towel - the bolts now stand up. Tighten the nut on every bolt against the board with the wrench; if a bolt turns with the nut, hold its head from behind with the second wrench or pliers.
  5. Set the heights. Each piece floats at its own height above the board; that is what gives the terrain look. The table on the next page gives the gap for each piece. On every bolt of that piece, spin a second nut down until the top of the nut is exactly the gap above the board - measure it with the ruler. All bolts of one piece get the same gap, so the piece sits level. (If a gap is very small, the piece simply rests on the nut from step 4.)
  6. Put the pieces on. Now use the front map. Take piece 1, line its holes up with its bolts (they share the number: 1a, 1b ...) and lower it onto the nuts. Spin a nut onto each bolt on top and tighten by hand, then a quarter turn with the wrench. Do not force it - snug is enough. Repeat for every piece in any order.
  7. Hang it. The finished piece weighs about 26 lb (12 kg). Fix the board to the wall through 2 wall studs with 1/4 in × 3 in lag screws (drill small pilot holes first); the screws go through the board between the bolts. Two people should lift it. Keep the top edge up, as on the maps.
  8. Last look. Look at it from the side: every piece should sit level. If one tilts, loosen its top nut, adjust the nut under it, and tighten again.

Each piece: its bolts and how high it sits

PieceSizeIts bolts (and holes)Bolt lengthGap under the pieceWeight
117.5 in × 18.4 in1a, 1b2.75 in0.45 in2.7 lb
225.3 in × 24.0 in2a, 2b3.00 in0.89 in2.5 lb
317.0 in × 24.0 in3a, 3b3.50 in1.34 in2.1 lb
421.6 in × 23.0 in4a, 4b4.00 in1.78 in2.0 lb
511.9 in × 19.3 in5a, 5b4.50 in2.23 in1.6 lb
613.9 in × 22.7 in6a, 6b5.00 in2.67 in0.9 lb
78.9 in × 4.1 in7a, 7b5.50 in3.12 in0.4 lb
83.2 in × 9.2 in8a, 8b6.00 in3.56 in0.3 lb
91.1 in × 2.8 in9a, 9b6.50 in4.00 in0.0 lb

The gap is measured from the front of the board to the top of the nut the piece rests on. Bolts are 0.250 in hex bolts with nuts to match; a washer under each top nut is a nice touch but not needed.

Measurements and a ruler

Board thickness0.79 in (20 mm)the backing board and every wood piece
Bolt0.250 in hex bolt9 lengths: 2 × 6.50 in, 2 × 6.00 in, 2 × 5.50 in, 2 × 5.00 in, 2 × 4.50 in, 2 × 4.00 in, 2 × 3.50 in, 2 × 3.00 in, 2 × 2.75 in
Nut7/16 in wrencheach nut is about 0.22 in (6 mm) thick - a bolt needs at least that much thread showing to take a nut
Height of the boxesat least 7.5 in (191 mm)the longest bolt hangs 5.71 in (145 mm) below the board while you put the bolts in
Piece 1: gap under it0.45 in (11 mm)bolt 2.75 in: board 0.79 + gap 0.45 + piece 0.79 + top nut 0.22 = 2.24 in, leaving 0.51 in of bolt showing above the top nut
Piece 2: gap under it0.89 in (23 mm)bolt 3.00 in: board 0.79 + gap 0.89 + piece 0.79 + top nut 0.22 = 2.68 in, leaving 0.32 in of bolt showing above the top nut
Piece 3: gap under it1.34 in (34 mm)bolt 3.50 in: board 0.79 + gap 1.34 + piece 0.79 + top nut 0.22 = 3.13 in, leaving 0.37 in of bolt showing above the top nut
Piece 4: gap under it1.78 in (45 mm)bolt 4.00 in: board 0.79 + gap 1.78 + piece 0.79 + top nut 0.22 = 3.57 in, leaving 0.43 in of bolt showing above the top nut
Piece 5: gap under it2.23 in (57 mm)bolt 4.50 in: board 0.79 + gap 2.23 + piece 0.79 + top nut 0.22 = 4.02 in, leaving 0.48 in of bolt showing above the top nut
Piece 6: gap under it2.67 in (68 mm)bolt 5.00 in: board 0.79 + gap 2.67 + piece 0.79 + top nut 0.22 = 4.46 in, leaving 0.54 in of bolt showing above the top nut
Piece 7: gap under it3.12 in (79 mm)bolt 5.50 in: board 0.79 + gap 3.12 + piece 0.79 + top nut 0.22 = 4.91 in, leaving 0.59 in of bolt showing above the top nut
Piece 8: gap under it3.56 in (90 mm)bolt 6.00 in: board 0.79 + gap 3.56 + piece 0.79 + top nut 0.22 = 5.35 in, leaving 0.65 in of bolt showing above the top nut
Piece 9: gap under it4.00 in (101 mm)bolt 6.50 in: board 0.79 + gap 4.00 + piece 0.79 + top nut 0.22 = 5.79 in, leaving 0.71 in of bolt showing above the top nut
How far it stands off the wall5.57 in (141 mm)board + the biggest gap + a piece (plus the top nuts)
Wall screws1/4 in × 3 in lag screwsinto 2 studs; the whole piece weighs 26 lb (12 kg)

The ruler on the right is true size when this page is printed at 100 % (no "fit to page"). Check it against a real ruler once: the marks 1 and 2 should be exactly one inch apart. Use it to tell the bolt lengths apart and to set the gaps.

12345678912345678910111213141516171819202122in | cm